华为无线网络射频调优及WLAN跨VLAN的三层漫游示例

华为无线网络射频调优及WLAN跨VLAN的三层漫游示例(2)

更新：2024-04-03 00:46:35 来源：IT袋作者：马勇

导读：华为无线网络射频调优及WLAN跨VLAN的三层漫游示例，配置汇聚交换机SwitchB：接口 GE0/0/1 加入 VLAN10 、 VLAN101 和 VLAN102 接口 GE0/0/2 加入 VLAN100 接口 GE0/0/3 加入 VLAN101 和 VLAN102 ，创建接口 VLANIF100 ，地址为 10.

华为无线网络射频调优及WLAN跨VLAN的三层漫游示例

配置汇聚交换机SwitchB：

接口GE0/0/1加入VLAN10、VLAN101和VLAN102
接口GE0/0/2加入VLAN100
接口GE0/0/3加入VLAN101和VLAN102，
创建接口VLANIF100，地址为10.23.100.2/24。

<HUAWEI> system-view
[HUAWEI] sysname SwitchB
[SwitchB] vlan batch 10 100 101 102
[SwitchB] interface gigabitethernet 0/0/1
[SwitchB-GigabitEthernet0/0/1] port link-type trunk
[SwitchB-GigabitEthernet0/0/1] port trunk allow-pass vlan 10 101 102
[SwitchB-GigabitEthernet0/0/1] quit
[SwitchB] interface gigabitethernet 0/0/2
[SwitchB-GigabitEthernet0/0/2] port link-type trunk
[SwitchB-GigabitEthernet0/0/2] port trunk allow-pass vlan 100
[SwitchB-GigabitEthernet0/0/2] quit
[SwitchB] interface gigabitethernet 0/0/3
[SwitchB-GigabitEthernet0/0/3] port link-type trunk
[SwitchB-GigabitEthernet0/0/3] port trunk allow-pass vlan 101 102
[SwitchB-GigabitEthernet0/0/3] quit
[SwitchB] interface vlanif 100
[SwitchB-Vlanif100] ip address 10.23.100.2 24
[SwitchB-Vlanif100] quit

配置Router的接口：

接口GE1/0/0加入VLAN101和VLAN102
创建接口VLANIF101并配置IP地址为10.23.101.2/24
创建接口VLANIF102并配置IP地址为10.23.102.2/24。

<Huawei> system-view
[Huawei] sysname Router
[Router] vlan batch 101 102
[Router] interface gigabitethernet 1/0/0
[Router-GigabitEthernet1/0/0] port link-type trunk
[Router-GigabitEthernet1/0/0] port trunk allow-pass vlan 101 102
[Router-GigabitEthernet1/0/0] quit
[Router] interface vlanif 101
[Router-Vlanif101] ip address 10.23.101.2 24
[Router-Vlanif101] quit
[Router] interface vlanif 102
[Router-Vlanif102] ip address 10.23.102.2 24
[Router-Vlanif102] quit

5.2、配置`AC`与其它网络设备互通

# 配置AC的接口GE0/0/1加入VLAN100，并创建接口VLANIF100。

<AC6605> system-view
[AC6605] sysname AC
[AC] vlan 100
[AC-vlan100] quit
[AC] interface vlanif 100
[AC-Vlanif100] ip address 10.23.100.1 24
[AC-Vlanif100] quit
[AC] interface gigabitethernet 0/0/1
[AC-GigabitEthernet0/0/1] port link-type trunk
[AC-GigabitEthernet0/0/1] port trunk allow-pass vlan 100
[AC-GigabitEthernet0/0/1] quit

配置AC到AP的路由，下一跳为SwitchB的VLANIF100。

[AC] ip route-static 10.23.10.0 24 10.23.100.2

5.3、配置DHCP服务为AP和STA分配IP地址

# 在SwitchB上配置DHCP中继，代理AC分配IP地址

[SwitchB] dhcp enable
[SwitchB] interface vlanif 10
[SwitchB-Vlanif10] ip address 10.23.10.1 24
[SwitchB-Vlanif10] dhcp select relay
[SwitchB-Vlanif10] dhcp relay server-ip 10.23.100.1
[SwitchB-Vlanif10] quit